The Wabbit 3d printed injector razor pass around.

Discussion in 'Safety Razors' started by BBS, Jun 10, 2020.

?

If the designs were made public on thingverse would you have this razor printed for personal use?

  1. Yes

    27 vote(s)
    93.1%
  2. No

    2 vote(s)
    6.9%
  1. Terry

    Terry Tool Admirer

    Good afternoon fellow wanbit-iers.
    I ran out of time this morning to report.
    Took the black one for a tour this morning.
    New B-20 blade of course, different soap and brush.

    20200917_131331.jpg
    I got another great shave again!
    These razors seem to have it where it should be. I like a lite razor, especially on the gord. The handle is easy grip for me and long enough to get the proper placement of the hand.
    3 passes face and gord, no issues, none.
    Smooth and clean, just as I like it.
    I also find it easy to find the correct angle too. I just shave away like I've used this thing since childhood.
    Only the 3rd shave and I'm quit comfortable with them.
    Nice.
    Well lucky me to get to try these out.
    Till Friday!

    tp
     
  2. Terry

    Terry Tool Admirer

    Ok Wabbit-tiers....
    Sorry so late.
    The black Wabbit did it's job well today.
    20200918_184550.jpg
    Another fine shave to say the least.
    I had one boo-boo, a bump on the cheek was in need of removal, so it was. That's a normal kinda thing for me, when one uh... pops up. Not much blood, just enough to know it was flattened out.
    Gonna do a Saturday purple shave then send them off to the next luck Wabbit-tier.
    So here is what I think of these tools.

    Pros.
    1. The shave is excellent.
    2. I like a light razor so that's a plus.
    3. Even though it needs washed more to stop clogging, it cleans quickly.
    4. No injector to load the thing.

    Cons.
    1. It is difficult to load and unload a blade.
    2. I don't own one, worse yet two.

    What I would change.
    1. I would file a notch in the back of the top cap so it would be easier to tell front from back.
    2. I would file down about an 1/8 of an inch on the ends of the top cap just enough to get my finger nails under the blade to remove it.

    That's my 2¢.

    If your gonna make some for use few poor Wabbit test subjects.
    Put me down for 1 black one and 1 purple one please.


    Thanks for letting me in on this.

    tp
     
    Jayaruh, GAW9576, Karl G and 3 others like this.
  3. brit

    brit in a box

    awesome Terry.cool pic..:cool:
     
    GAW9576, Karl G and Terry like this.
  4. twhite

    twhite Peeping Tom

    I actually have a V3 that takes care of a few issues. I have added additional cutouts for round magnets. This is a huge help for our friends across the pond. The second and biggest change is the handle. I redesigned it using @riverrun Enders style handle. Yes the exact same that is on the TNNSER. I hope to have a sample printed up next week. I know Andreas is getting one printed.

    Sorry I don’t have any pictures
     
  5. twhite

    twhite Peeping Tom

  6. Terry

    Terry Tool Admirer

    Thanks Gary!


    Really Tom!
    I like the handle on this one.
    But I'm willing to try another one if you need another tester.
    :)

    tp
     
    GAW9576, Karl G, twhite and 2 others like this.
  7. GAW9576

    GAW9576 Well-Known Member

    Karl G, Edison Carter and MrEE like this.
  8. MrEE

    MrEE Half Naked Shave Stalker

    I'd just like to print one myself.
     
    jaro, Karl G, GAW9576 and 2 others like this.
  9. twhite

    twhite Peeping Tom

    That is in the near future. Still getting feedback from a few Pass arounds.
     
  10. riverrun

    riverrun Well-Known Member

    ischiapp, Ron R, Karl G and 4 others like this.
  11. GAW9576

    GAW9576 Well-Known Member

    I'm looking forward to my turn with the Wabbit. Also if anyone is printing a few TNNSERs or doing another group buy I'd be interested.
     
    Karl G, Edison Carter and Terry like this.
  12. riverrun

    riverrun Well-Known Member

    ischiapp, jimjo1031, Ron R and 4 others like this.
  13. Terry

    Terry Tool Admirer

    Hello and good morning Wabbit-tiers.

    Well an end to a wonderful run with two great razors. Another great head-n-face shave as all the others were.
    No issues, none, just clean and smooth like I like.
    Used a different brush I reknoted yesterday along with some Bay Rum I haven't used for a while.

    20200919_084536.jpg
    I'll send these little tools to Jim @Jim99 as soon as I get to the post office, that might be Monday, they close early today.

    This was fun, and I can't wait till the next tool to arrive in the mail to, test drive.
    Everyone.
    Enjoy!

    tp
     
    Karl G, GAW9576, twhite and 2 others like this.
  14. Jim99

    Jim99 Gold Water Shaver

    I’m patiently awaiting the arrival of the wabbits.
     
    Karl G, Terry, GAW9576 and 1 other person like this.
  15. jaro

    jaro the dread and the fear

    Me too..
     
  16. BBS

    BBS Well-Known Member

    I think I echo Tom's sentiments on this, it is not that he doesn't want to make the design files public it is he doesn't want design files made public with design flaws or other usability issues hence the pass around first.
     
  17. BBS

    BBS Well-Known Member

    Wouldn't it be easier to redesign the razor head to attach to the TNNSER handle instead? You'd also have to redesign the fastening method to be easier to change razors heads. Once that is done then you can add new razor heads like a 3d printed wedge blade holder to the platform building on a modular fashion.
     
  18. jaro

    jaro the dread and the fear

    I know which is fine . I can gladly wait until its ready for public consumption......
     
    GAW9576, riverrun and twhite like this.
  19. twhite

    twhite Peeping Tom

    This is it exactly. On the Wabbit, I will most likely release both handle designs.
     
    GAW9576, Edison Carter and riverrun like this.
  20. twhite

    twhite Peeping Tom

    I will need to look into this. Very sound idea.
     
    GAW9576 and riverrun like this.

Share This Page